@weedeater, EMMA, The stringers head may not have the string wrapped properly onto it. Remove all the string and replace the nylon line with appropriate/compatible line and try. If this does not do the trick disassemble the string spool head and check for dirt/debri(clean head) check for damage, rethread and try.
How do I stop my trimmer from auto feeding?
How do I stop my trimmer line coming out?
What is automatic feed spool?
The Automatic Feed Spool (AFS) is the technologically advanced line feed system found on Black & Decker string trimmer products. Using centrifugal force, the system monitors the amount of line being used and feeds more line automatically as the cutting line shortens.
Why does my string keep coming out of my weed wacker? – Related Questions
Why is my trimmer pulling my hair?
Why does my trimmer bog down when I give it gas?
The most common causes of a weed eater dying when throttled are fuel issues, insufficient air intake, or problems with the exhaust.
Why does my trimmer only run on full choke?
When your trimmer starts and runs on choke, it could be because the check valve in the gas cap is clogged. Start the trimmer and gently unscrew the gas cap halfway off. Turn the choke off and assess. If the engine is still running, that means the gas cap may be the culprit.
How do you adjust the idle on a trimmer?
Where is the idle adjustment screw?
How do you adjust a 2 stroke idle screw?
Which way do you turn a idle screw to lower idle?
What happens if idle is too high?
High idle speeds waste fuel, cause extra wear and tear on your engine, and can be unsafe as well. If your foot should slip off the brake as the engine revs, it could cause your vehicle to lurch forward, putting other drivers and even pedestrians at risk.
How many turns out should the idle screw be?
It’s important that all idle mixture screws be adjusted the same way so that the output from the carburetor idle circuit is balanced across both idle mixture outlets. One to 1½ turns out is a typical place to start.
How do I know if my idle is too low?
A car that’s having idling problems will show several symptoms, including:
- Bouncing or shaking during idle.
- Inconsistent/jumping RPMs.
- Skipping/shaking sounds.
- Idling below 600 RPMs.
How long of an idle is too long?
Idling your car for 30 seconds to a minute is acceptable, and it will not cause any harm to your vehicle. With advanced technology, even if you let your car idle for a slight longer duration, it will not damage it.
What causes a weak idle?
Causes of a rough idle. Many different problems could result in a rough idle for your car or truck, including: dirty fuel injectors, clogged air filters, bad spark plugs, and a variety of exhaust system issues. Let’s go over each of these causes in more detail and learn how they can be remedied.
How can you tell if idle is rich or lean?
Heavy black carbon on the exhaust tailpipe would tell you the air-fuel mixture is much too rich. On the flip side, a blistered or yellowish appearance on spark plug electrodes indicates an overly lean fuel ratio.
What happens when you run a 2 stroke too rich?
keeping the engine under a light load (you will only be opening the throttle to 1/2 or so) If the needle is set too rich you will hear a sputtering like the choke is on and the acceleration will be slow. If the clip position is too lean the engine will sound quiet and have a “dead” feeling possibly hesitating.
Does backfire mean rich or lean?
Lean Air/Fuel Mixture
Not only can a rich air/fuel ratio cause a backfire, a mixture that doesn’t have enough gasoline can cause a backfire, too. A “lean” mixture is one that doesn’t have enough fuel, and too much air.
How do I know if my fuel mixture is too lean?
Here are some of the most common symptoms of how to recognize when your engine is running lean.
- Starting Trouble. This symptom shouldn’t come as a surprise because vehicles need fuel to start.
- Decrease In Performance.
- Clean Spark Plugs.
- Check Engine Light.
- Stalling Engine.