What would cause a Troy Bilt lawn mower not to start?

There may be old or bad fuel in the carburetor float bowl. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and prevent the engine from starting. If the carburetor is clogged, try cleaning it with carburetor cleaner.

What is the first thing to check if a lawn mower won’t start?

Your Mower Won’t Start:
  1. Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten.
  2. Dirty Air Filter: Clean or replace.
  3. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas. If this doesn’t work, you might need a new fuel filter.

What is the most common reason a lawn mower won’t start?

It’s a common problem to have, but there’s often a quick and easy fix if you can diagnose the problem. Some of the most common reasons a lawn mower won’t start include low fuel, spark plug issues, a clogged carburetor, a broken clutch, or broken gears.

Table of Contents

How do I force my lawnmower to start?

If you run into problems getting your lawnmower ready for springOpens a new window, try the following:
  1. Use fresh gas.
  2. Check the spark plug.
  3. Use the choke.
  4. Prime the mower.
  5. Check the air filter.
  6. Check the cables.
  7. Check for water in the fuel tank.
  8. Clear the starter cord of blockages.

What would cause a Troy Bilt lawn mower not to start? – Related Questions

Why won’t my lawnmower start when I pull the cord?

Why will my Briggs and Stratton engine not start?

Disconnected, dirty or fouled spark plugs are common causes for engines that won’t start. For small engines, spark plugs typically need to be replaced every season or after 25 hours of use. You should also check to make sure the spark plug gap is set correctly.

How do I get my lawn mower to start after sitting?

To get the mower started, you may have to change the gas and clean or change the plug.
  1. Check the oil before you start a four-cycle mower that has been sitting for a long time.
  2. Prime the engine by pushing the priming bulb three times.
  3. Give the spark plug wire a little tug to see if it’s loose.

How do you bypass a starter on a lawnmower?

How to bypass a solenoid starter on a lawnmower, step by step

Why is it so hard to start my lawn mower?

The fuel filter might be clogged. A clogged fuel filter is most commonly caused by leaving old fuel in the lawn mower. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and make the engine hard to start.

Can you use wd40 to start a lawn mower?

What can I spray on my lawnmower to start?

What can be used instead of starter fluid?

Starting Fluid Substitutes

As discussed you can use carby (carburetor) spray as an alternative to starting fluid. We do recommend specific engine starting spray when available as the pressure is lower and the nozzle on the can creates more of a mist.

How do you fix a lawn mower that won’t start?

  1. Change the lawn mower carburetor filter.
  2. Check the spark plug.
  3. Clear the mower deck of debris.
  4. Clear the vent in the lawn mower fuel cap.
  5. Clean and refill the lawn mower fuel tank.
  6. Add fuel stabilizer to the tank.
  7. Inspect the safety release mechanism cable.
  8. Check to see if the flywheel brake is fully engaged.

How do I know if my lawn mower carburetor is clogged?

Dirty Carburetor Symptoms
  1. The lawn mower engine has trouble starting.
  2. The engine starts but stalls while you’re cutting the lawn.
  3. The engine runs rough during mowing.
  4. Black smoke is seen coming out of the muffler.
  5. There is a noticeable increase in fuel consumption during normal lawn mower use.

How do you clean a clogged carburetor on a lawn mower?

  1. STEP 1: Clean the outside of the lawn mower engine.
  2. STEP 2: Remove the air filter to access the carburetor.
  3. STEP 3: Remove the carburetor.
  4. STEP 4: Disassemble the carburetor.
  5. STEP 5: Replace any worn-out parts.
  6. STEP 6: Clean the carburetor and carburetor parts.
  7. STEP 7: Reassemble the carburetor.

What would cause a lawn mower not to fire?

Self-explanatory, it’s a plug that’s contaminated by too much gas (flooding), carbon, or oil. All of these will prevent the plug from doing its job. Flooding may be caused for a few reasons – blocked air filter, faulty choke, overuse of choke, tipping mower over on its carburetor side, and carburetor fault.

See also  How do I know if my riding lawn mower solenoid is bad?

Why is my lawn mower not getting any spark?

If no spark appears, check for broken wires, shorts, grounds or a defective stop switch. Once you have confirmed that the stop switch is working, reconnect the spark plug lead.

What would cause no spark to spark plugs?

Loss of spark is caused by anything that prevents coil voltage from jumping the electrode gap at the end of the spark plug. This includes worn, fouled or damaged spark plugs, bad plug wires or a cracked distributor cap.

What will cause a motor not to fire?

From the spark plugs to the ignition coils, many different things can cause an engine to misfire. The most common causes of misfires are worn, improperly installed, and mishandled spark plugs, malfunctioning ignition coils, carbon tracking, faulty spark plug wires and vacuum leaks.

What are the common faults causing the motor not to start?

The most common cause of motor failure, and arguably the most difficult to overcome, is low resistance. Low resistance is caused by the degradation of the insulation of the windings due to conditions such as overheating, corrosion, or physical damage.

Leave a Comment