The setting that you will use when applying Bifen Granules with a Scotts Edgeguard DLX is a 2 or a 3 depending on how quickly you walk. 141 of 151 people found this answer helpful.
What setting to put Scotts spreader on?
How do you determine spreader settings?
Calibrating Your Spreader
- Divide 100 by the square foot the bag of fertilizer covers.
- Multiply the weight of the bag by this number.
- The answer is the amount of fertilizer needed to cover 100 sq. ft.
- Place this amount in the spreader.
- Mark off a 10 ft. x 10 ft. area.
- Apply using the suggested setting.
What do the numbers mean on a Scott’s spreader?
The numbers stand for an application rate. A bag of commercial fertilizer will usually have numbers for where to set either broadcast or drop spreaders to get the recommended amount of fertilizer laid down.
What setting is Scotts EdgeGuard? – Related Questions
How do you use the Scotts EdgeGuard spreader?
What does EdgeGuard do on Scotts spreader?
This lawn spreader comes pre-calibrated and ready-to-use, and holds up to 15,000 sq. ft. of Scotts® product. When EdgeGuard™ is engaged, it will block off the right-side of the spreader pattern to prevent product from spreading onto non-lawn areas.
What number should fertilizer spreader be on?
Place your spreader setting on a low setting (usually one-fourth of the spreader setting range or less). Spread the material over a 50 x 20-foot area (1,000 square feet). If there is material left over, increase your setting. If you come up short, decrease your setting.
What do the settings mean on a drop spreader?
In general, the smaller you set your spreader setting the smaller the hole and the slower the material releases from the hopper. There are many different brands of spreaders on the market, and, new or old, it is highly recommended to properly calibrate your spreader before the first use in the spring.
What are the numbers on Scotts Turf Builder?
A: Thank you for your question regarding Scotts Turf Builder Lawn Fertilizer. Those numbers are the NPK. Which is the amount of Nitrogen, Phosphorous, and Potassium in the product. The NPk for this product is as follows: Nitrogen-32, Phosphorous-0, Potassium-4.
What spreader setting should I use for Scotts EZ seed?
Put your EZ seed in the hopper, set your scotts spreader at the max setting and walk back and forth spreading it as evenly as possible.
What setting should I use on Scotts Edgeguard spreader for lime?
Pelletized lime should be applied every other year (approximately 15 lbs./1,000 ft²) once you have your soil pH to its optimum level, which is between 6.0 and 6.5.
Lime.
| Spreader |
Setting |
| Scotts (Drop) |
11.5 |
| Scotts (Broadcast) |
J |
| Earthway EV-N-SPRED |
21 |
| Greenview |
3 or 4 |
How do I calibrate my Scotts spreader?
What setting should I use to overseed my lawn?
Set your mower at two inches or less for regular overseeding. For southern lawns and winter color, set the blade as low as it goes, and cut just above the soil—what’s known as scalping.
Is it better to overseed or fertilize first?
Stop fertilizing for at least a month before overseeding. The fertilizer makes your grass grow faster, which makes it harder for the new seeds to take hold.
Can you apply too much overseed?
If you put down too much grass seed, you will encourage competition that will cause your grass seedlings to struggle after germination because there will be excessive competition for sunlight, soil nutrients, and water.
Can you put too much grass seed down?
Too much grass seed causes undue competition for resources such as light, water and nutrients, and grass seedlings struggle as a result. Too little seed leaves lawns thin or bare.
Should grass seed sit on top of soil?
Will grass seed germinate on top of the soil? Yes; in fact, germination will suffer if too much soil is placed on top of the seeds. The experts at Jonathan Green recommend placing a thin layer of mulch or topsoil over them to help keep them moist and warm and promote growth.
Do you cover grass seed after spreading?
After spreading the seed, cover the area with a mulch of straw, fine compost, or mushroom soil.
Does grass seed need to be buried?
Once you finish spreading the seed, use a rake to lightly work it into the soil at a depth of about 1/4 inch. Don’t bury the seeds any deeper; grass seed needs adequate light to germinate quickly. After raking, pass over the area with a roller, which helps ensure the good seed-to-soil contact your new seed needs.
Does putting grass clippings on bare spots help grass grow?
Simply put, grass clippings are good for lawns because they turn into natural fertilizer. Clippings contain the same things as the rest of your grass – including water and the nutrients (especially nitrogen) that your lawn needs to stay healthy.