The choke on symbol for most small engines looks like a horizontal ( — ) or diagonal ( / ) line. It also can simply say ‘Choke’, ‘Full Choke’, or ‘Start’. The off symbol for most small engine chokes is represented by a vertical line ( | ) or the word ‘Run’.
Which position is choke on?
Typically the “choke” is on when the choke lever is in the up position or when the choke lever is inline with the handle bars on your bike. Choke on means that the choke plate is covering the carb throat.
Is the choke open or closed?
Normally choke will be in open position, in which valve is parallel to the air flow, and has no effect on the air flow. When choke is actuated by mechanical or by pneumatic method, it rotates an angle restrict the air flow (closed position).
What symbol is choke on Stihl?
Stihl chainsaws denote the choke position using a nearly horizontal squiggle between two vertical lines at the lowest position on the master control lever.
What is the choke on symbol? – Related Questions
How do you tell if choke is on or off on dirt bike?
What is choke mode?
What is a Common Mode Choke? A common mode choke is an electrical filter that blocks high frequency noise common to two or more data or power lines while allowing the desired DC or low-frequency signal to pass.
Which way is choke on a Stihl trimmer?
Which way is the choke on a Stihl leaf blower?
Which way is choke on Stihl hedge trimmer?
How do you use a Stihl choke?
STARTING YOUR CHAINSAW
- Depress the throttle lock and throttle, and move the control lever to full choke (i.e. moved to the limit of its travel).
- Firmly press the primer (if fitted) 2–3 times.
- Place the saw on the ground.
- Once the saw has ‘fired’, move the choke up to the “half-choke” position and pull over.
What happens if choke is always on?
Leaving the choke on for too long will cause unnecessary engine wear and waste fuel. This is also bad for the environment. The choke is mainly used during winter to help with starting. The engine needs its fuel to be vaporised in order to burn it.
When should you turn on choke?
When an engine is cold it doesn’t vaporize fuel efficiently, resulting in rough idling and stalling. The choke should be used to “choke” the flow of air and allow for a richer fuel mixture. Only use the choke when starting your engine under cold conditions. Once you’re up and running smoothly turn it off.
How do you start a chainsaw with a choke?
In either case, your goal is to get the fuel flowing and get your saw’s engine warm enough to fire.
- Set Your Chain Brake.
- Close the Choke.
- Press the Decompression Valve.
- Press the Primer Bulb.
- Set the Choke to “Run” or “On”
- Pull the Cord Again.
- Set the Engine to “Low Idle”
What is the safest way to start a chainsaw?
What is the proper way to start a chainsaw?
How do I make my chainsaw easier to start?
How many pulls should it take to start a chainsaw?
With the choke in the “off” position, pull the engine’s crank cord through again. The engine should start in 1 to 3 pulls. Try it first without using the throttle control—unless recommended by the manufacturer.
Should you start a chainsaw with the chain brake on?
When engaged, the chain brake stops the chain from rotating around the saw’s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
Why does my chainsaw kickback when I try to start it?
What Causes Chain Saw Kickback? There are two circumstances that can cause kickback when using a chain saw. The first occurs when the moving chain at the tip or the nose of the guide bar strikes an object. The second situation is when the wood closes in, pinching the saw chain in the middle of the cut.
What should you not do with a chainsaw?
Other safety precautions to remember when operating a chainsaw: Never walk around with a chainsaw in the operating mode, always switch off the power source. Do not attempt to cut anything other than wood with a chainsaw. Cut only one piece of wood at a time, never two branches at once.