Why is my Craftsman leaf blower not starting?

If the carburetor is clogged, try cleaning it with carburetor cleaner. If cleaning the carburetor isn’t effective, rebuild or replace the entire carburetor. The recoil starter assembly engages the crankshaft to turn over the engine. If the recoil starter assembly is defective, the leaf blower won’t start.

What do you do if your gas leaf blower won’t start?

Top 6 Reasons Your Gas Blower Won’t Start
  1. Primer bulb wasn’t pressed enough. Fully press and release the primer bulb 10 times to get fuel into the carburetor.
  2. Fueled up? Make sure the tank has plenty of properly mixed fuel.
  3. Old/improperly mixed fuel.
  4. Check the air filter.
  5. Engine may be flooded.
  6. Spark plug issues.

Why is my Craftsman leaf blower not starting? – Related Questions

How do I know if I flooded my leaf blower?

How do you clean the carburetor on a gas leaf blower?

Detach the tube from the end opposite the fuel tank, which is where the carburetor is located, and drain any fuel inside it. Spray carburetor cleaner into the hole where the tube had been attached and reattach the tube. The cleaner will start to remove built-up residue the next time you use your blower.

How do you reset a leaf blower?

Leaf Blower Revolution – Idle Game

where is misc? Open the main menu (the top left corner icon, or press escape), select ‘misc’ from the tabs at the bottom of the menu, and choose the Hard Reset option.

How do you unclog a fuel filter on a leaf blower?

Pull the fuel filter from the housing and remove the pre-filter from the rest of the unit. Wash the pre-filter using soapy water and place it for about an hour on a rag or paper towel to dry. Remove the felt filter element and either blow it out using a can of air or clean it using a paintbrush.

See also  What oil is compatible with Hy-Gard?

How do I start my gas air blower?

How do I know if my blower motor isn’t working?

If the blower motor isn’t running you should:
  1. Use voltmeter or ohmmeter to check for a blown fuse. If you find one, replace it.
  2. Start car and see if blower motor works.
  3. If the circuits are in good repair but the blower motor keeps blowing fuses, replace the blower motor [source: You Fix Cars].

Where is the blower motor reset button?

It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.

What would cause the blower motor to stop working?

Blower motors are designed to circulate air, so they won’t work if there’s no air to move. You should always check the filters and vents surrounding the blower to make sure that the blower isn’t having a hard time working. Look into your air filter’s housing and check the markings on your filter.

How do I reset my blower motor?

How to Find and Reset your Furnace Motor Blower
  1. Step 1: Turn off the power to the furnace.
  2. Step 2: Remove the blower compartment cover.
  3. Step 3: Make sure the blower is completely cooled off.
  4. Step 4: Locate the reset button.
  5. Step 5: Press the button in (assuming that this is your issue and that the button has popped).

How do I know if my blower motor relay is bad?

One of the first symptoms of a problem with the blower motor relay is a blower motor that does not function. As the relay is the switch that supplies current to the blower motor, if it fails internally, then power may be cut off from the blower motor circuit causing the motor to no longer function.

How can you tell if a fan fuse is blown?

Remove the fuse from its holder. In some cases you may need a small screwdriver to unscrew the fuse holder cap. Look at the fuse wire. If there is a visible gap in the wire or a dark or metallic smear inside the glass then the fuse is blown and needs to be replaced.

How do I know if my AC blower fuse is bad?

Test the load: If you saw a voltage reading during the previous step, run the same test on the “load” side of the fuses. You should again see a reading between 220 and 240. If you see a voltage reading on the “line” side but not the “load” side, it means you have a blown fuse.

Where is the blower motor fuse relay?

Leave a Comment