A clogged carburetor is most commonly caused by leaving fuel in the hedge trimmer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to stall or run roughly.
Why is my hedge trimmer blade not moving?
If your engine runs, but the trimmer blades do not move when the throttle is engaged, the clutch may be broken or improperly tensioned. The clutch is attached to the crankshaft, and engages the gearbox to start rotating once a certain rotational speed is reached.
Why is my trimmer over revving?
If the engine is running fast (revving high):
Make sure that the choke is disengaged and the throttle hold has been reset by pressing the trigger. You can check the throttle cable to make sure there are no kinks found in it – however this requires a mechanical proficiency to strip down the machine uncovering the cable.
How do I fix my hedge trimmer not working?
Common solutions for: Hedge trimmer won’t start. Inspect the spark plug for signs of wear or damage. If the porcelain insulator is cracked, an electrode is burned away or damaged, or there is heavy carbon buildup at the electrode, replace the spark plug.
Why does my Stihl hedge trimmer keep cutting out? – Related Questions
Why did my trimmer stop working?
It is possible that your Trimmer does not turn on or move because it is dirty. There can be hair or dirt particles stuck inside it, causing the cutting unit to be blocked. To fix this problem, properly clean your Trimmer. Remove the cutting unit and clean your Trimmer from the inside as well.
Why is my hedge trimmer not cutting?
If there is debris ensure the machine is powered off when removing any blockages. Check the blades for any damage as a damaged cutting blade could cause the machine to stop working. If the blades are damaged your local garden repair shop should be able to fix this for you. Ensure your blades are lubricated.
Can you spray WD-40 on a hedge trimmer?
Do not use WD-40 to lubricate your hedge trimmer. WD-40 is marketed as a household lubricant, not for lawn equipment. WD-40 does not have the required lubricants or rust inhibitors to protect your hedge trimmer.
Can electric hedge trimmers be repaired?
With a severed cord, your hedge trimmer is virtually worthless. With a small amount of money and a little ingenuity, however, you can repair the cord and have the trimmer running. If the cord left attached to the trimmer is long enough to be useable, then you simply can add a new plug to its end.
What fuse does a hedge trimmer?
Your hedge trimmer is fitted with a moulded plug. However if you need to replace a fitted plug then follow the instructions below. If a 13AMP (BS1363/A) plug is used, a 13A fuse must be fitted, or if any other type of plug is used a 13AMP fuse must be fitted, either in the plug or adapter, or on the distribution board.
Can I use WD-40 to lubricate hedge trimmer?
Keeping the blades clean and lubricated with a penetrating oil, such as WD-40, improves the performance and extends the life of your hedge cutters.
What kind of grease do you use in a Stihl hedge trimmer?
Stihl Genuine 0781 120 1109 80g Gear Lubricant A/B.
How do you lubricate a Stihl hedge trimmer?
How often should you grease a hedge trimmer?
For best operation and longer lifetime, lubricate the hedge trimmer gear case with a special grease after every 50 hours of operation.
Can you put too much grease in a bearing?
Overgreasing by applying too much grease to a bearing at one time can result in a seal failure and generate heat in the bearing housing. When too much grease is pumped into a bearing cavity, it eventually will become full. If there is no relief port on the housing, the grease will blow through the seals.
How do I lubricate my hedge trimmer blades?
Lubricate the Hedge Trimmer Blade
- Make sure the trimmer is unplugged and the blade is not moving.
- Make sure that the switch lock is released or in the OFF position.
- Use a rag to apply a light coat of machine oil along the edges of the top blade.
What is the best cleaner for hedge trimmer blades?
How? – Cleaning your hedge trimmer blades is as simple as wiping them down with soapy water and a cloth after each use. Applying a lubricant to the blades after cleaning them is also recommended. Try not to leave it too long between cleans and ideally, after every use is best.
Can you use WD-40 on trimmer blades?
No, WD40 cannot be used to replace clipper blade oil. It is very thin and will evaporate too quickly. It can also easily get into the clipper housing, which can thin the grease inside the clipper, causing problems. Only use oil, coolants, sprays or dips formulated specifically for dog clippers.
Do I need to lubricate my hedge trimmer blades?
For best operation and longer blade life, lubricate the hedge trimmer blade with a lightweight machine oil before and after each use.
How often should hedge trimmer blades be sharpened?
As such, we recommend sharpening after every 50 hours of use or so, to ensure consistent cutting performance and to enable you to enjoy your hedge trimmer for a long time to come.
How much does it cost to get hedge trimmers sharpened?
Sharpening cost
You can expect to pay anywhere from $20 to $40 to have the blades on your hedge trimmer sharpened. This is a very reasonable cost, considering that sharpening the blades will help to keep your trimmer running efficiently.