What setting do I put my spreader on for lime?

Adjust the spreader’s flow setting according to the manufacturer’s directions, generally between 3 and 5. Add approximately 40 to 50 pounds per 1,000 square feet to the spreader. As you apply the lime to the lawn, the broadcast spreader throws the prills in a 10- to 12-foot swath.

Can you spread lime with a lawn spreader?

What setting to put Scotts spreader on?

How do I know what spreader setting to use?

Calibrating Your Spreader
  1. Divide 100 by the square foot the bag of fertilizer covers.
  2. Multiply the weight of the bag by this number.
  3. The answer is the amount of fertilizer needed to cover 100 sq. ft.
  4. Place this amount in the spreader.
  5. Mark off a 10 ft. x 10 ft. area.
  6. Apply using the suggested setting.

What setting do I put my spreader on for lime? – Related Questions

What do the numbers on my Scotts spreader mean?

The numbers stand for an application rate. A bag of commercial fertilizer will usually have numbers for where to set either broadcast or drop spreaders to get the recommended amount of fertilizer laid down. The numbers on the bag may be different for various brands of spreaders.

What does EdgeGuard do on Scotts spreader?

This lawn spreader comes pre-calibrated and ready-to-use, and holds up to 15,000 sq. ft. of Scotts® product. When EdgeGuard™ is engaged, it will block off the right-side of the spreader pattern to prevent product from spreading onto non-lawn areas.

What should I set my spreader at for fertilizer?

Set your spreader so that the opening(s) in the bottom are ¾ open when engaged. Put 6.5 pounds or 1/5 of a bag of Milorganite into your spreader. Begin fertilizing your lawn, starting along an edge, and continue until the spreader is empty. Leave the spreader where it was when it ran out of Milorganite.

See also  How do I increase the speed of my lawn mower?

What is the best number to set a spreader for grass seed?

What setting do you use while spreading grass seed? Adjust your spreader to a low setting (usually one-fourth of the spreader setting range or less).

What setting do I put my drop spreader on for grass seed?

As with the broadcast spreader, you’ll get the best coverage — and avoid striping — by setting your spreader at 50 percent, and then spreading your seed two ways in a crosshatch pattern. Points to remember with drop spreaders include: They’re well-suited for small lawns (under 5,000 square feet).

What spreader setting should I use for Scotts EZ Seed?

Put your EZ seed in the hopper, set your scotts spreader at the max setting and walk back and forth spreading it as evenly as possible.

Can you drop too much grass seed?

If you put down too much grass seed, you will encourage competition that will cause your grass seedlings to struggle after germination because there will be excessive competition for sunlight, soil nutrients, and water. You’ll know if you seeded too heavy when the grass grows in very thick patches.

How fast do you walk with a drop spreader?

What is Correct? Homeowner spreaders are generally calibrated to deliver the correct rate and pattern at a walking speed of 2.75 mph. Professional spreaders, which are more likely to be pushed by physically fit young males, are typically calibrated at 3.0 mph.

Is a drop spreader better than broadcast?

Drop spreaders are particularly valuable when you must be precise in the product’s release, whereas a broadcast spreader’s main function is to efficiently broadcast in all directions. Drop spreaders will also make sure you don’t waste any product as you’re spreading.

See also  Is there a fuse in an electric pressure washer?

Is hopping more efficient than walking?

“In low gravity, like on the moon, skipping is more energetically efficient than walking,” Gregg said.

Do you overlap with a broadcast spreader?

Your current pass should spread product so it overlaps by a couple of feet the edge of the pattern of product spread from the previous pass (25% overlap).

How far does a Scotts broadcast spreader spread?

Up to 5,000 sq. ft.

How do I calibrate my Scotts broadcast spreader?

Are Scotts spreader settings lbs per 1000 sq ft?

per 5000 sq. ft. or 8 lbs per 1000 sq ft.

When should I spread Scotts 3 in 1?

Apply before the 3rd or 4th mowing of the year. A fall application may be made to control fall-germinating winter weeds and cool season perennial weeds such as dandelion and clover. On Bahiagrass and Centipedegrass lawns, wait until after the 2nd mowing of the year but DO NOT treat before mid-March.

Is Scotts speedy green 1000 a drop spreader?

Assembly of Scotts AccuGreen 1000 Parts

The Scotts AccuGreen 1000 drop spreader is a reliable and easy-to-use fertilizer spreader you can use to apply fertilizer evenly over your lawn.

Leave a Comment