How do you fix a weed eater that won’t stay running?

Most weed eaters will have a small air hole available on the cap to the gas tank – This lets air into the tank to help prevent any vacuum from forming. An easy way to check if your air hole is clogged is to simply loosen the cap while the trimmer is running – If performance improves, a replacement gas cap is your fix.

Why does my trimmer keep shutting off?

A clogged fuel filter is most commonly caused by leaving fuel in the string trimmer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and cause the engine to stall.

See also  What kind of gas does a Stihl weed eater use?

Why does my Stihl weed eater keep shutting off?

The trimmer can sputter and stall if it isn’t getting enough fuel, and that can happen simply because the fuel filter is dirty. Fuel filters are inexpensive, and it’s more practical to replace a dirty one than it is to try to clean it. On most models, it’s in the gas tank or on the cap.

How do you fix a weed eater that won’t stay running? – Related Questions

How do you clean a weed eater carburetor?

How do you clean a carburetor on a Stihl weedeater?

Why do you soak Stihl weed eater line in water?

Trimmer line does tend to dry out over time and becomes more brittle. Storing it or soaking it in water will help reduce line breakage and make the line more flexible. Be sure to deplete your supply of last year’s line before you purchase new line and begin using it.

How do you adjust a carburetor on a Stihl trimmer?

How many times do you prime a Stihl weed eater?

Things to Remember. With all gas-powered STIHL trimmers, you begin the starting procedure by pressing the fuel pump bulb at least 5 times.

How often do you grease a Stihl weed eater?

The Stihl maintenance schedule for weed eaters recommends checking and filling the gearbox with grease after every 25 hours of operation to keep internal metal parts lubricated.

What happens if you put too much oil in your Weed Eater?

If there is too much oil in the mixture, it can cause excessive smoke in the exhaust, oil leaking from the filter and loss of power. Too little oil allows the piston and cylinder to become hot and destroys the engine. You must first remove the old fuel and oil mixture to replace it with the correct ratio.

See also  What can I use instead of a plant saucer?

How long does the average Weed Eater last?

Your weed eater or weed whacker might live for ten years, but your battery might need to be replaced long before then. Look for warranties on the battery pack, but also pay note to how many volts it is in the first place. Battery solenoids will degrade over time.

How often should you change spark plug on STIHL Weed Eater?

STIHL recommends replacing the spark plugs around every 100 hours of use. It’s a good idea to get in the habit of checking the condition of your spark plug after every 10 to 15 hours of use. If the engine is running well, the outside electrode should have light brown deposits.

How do I know if my Stihl spark plug is bad?

Faulty spark plug warning signs

The engine requires repeated attempts to start or the engine won’t start at all. The engine misfires or runs rough. The engine starts, but stalls shortly after. There is a noticeable increase in fuel consumption during normal equipment use.

How do you check spark plugs without removing them?

Test with a spark plug tester

Attach a spark plug tester to the ignition wire. At the other end, the tester connects to the spark plug as it sits in your engine. Turn the ignition ON. Start the engine, or simply turn it over if it won’t start, and watch the transparent sides of the tester.

Can WD-40 clean spark plugs?

For part of your car repair and maintenance, you can use WD-40 to remove carbon residue, and keep moisture away from spark plugs and spark plug wires. “WD” stands for Water Displacement. So if your spark plugs are wet or you need to drive moisture away from ignition distributors, WD-40 can help!

What can ruin a spark plug?

Repeated overheating of the spark plug tip can cause the plug to prematurely fail. Overheating can be caused by many things like pre-ignition and a malfunctioning cooling system. Pre-ignition can lead to heat building up in the combustion chamber causing the spark plugs to fail.

Can you spray WD-40 in spark plug hole?

Q “Is it safe to spray WD-40 in a spark plug hole?” No, it’s a bad idea. WD-40 isn’t a great lubricant, it’s mostly a solvent and it will tend to wash oil off the cylinder walls which is absolutely not what you want to do before starting an engine.

Can you soak spark plugs in vinegar?

It is the same process if you’re curious about cleaning spark plugs with vinegar or petrol. With a wire brush, remove the carbon deposits from the plugs and soak the plugs in vinegar or petrol for a few seconds to remove the accumulated carbon deposits.

Leave a Comment